Amana Washer Stuck on Sensing Fill – Fixed

Amana Washer Stuck on Sensing Fill – In our modern age of technological innovation, we frequently underestimate the value of our domestic appliances, assuming that they will operate perfectly and without fail, every single day.

Amana washing machines, reputable for their efficiency and durability, are no exception. However, when your washer gets stuck on the ‘Sensing Fill’ stage, it can be a significant inconvenience. This extended guide will take you a step further in troubleshooting this common issue.

As we previously mentioned, your Amana washer might get stuck on the ‘Sensing Fill’ cycle due to water inlet valve issues, faulty load sensors, blocked water hoses, or control board malfunctions.

Although these are typically the main suspects, there could also be other less frequent factors contributing to the problem.

Amana Washer Stuck on Sensing Fill

Amana Washer Stuck on Sensing Fill

Is your Amana washing machine displaying a ‘Sensing Fill’ status but not progressing to the next washing stage? This common problem can be frustrating, but fear not! This complete manual will assist you comprehend why this occurs and propose suitable resolutions to get your washer back up and operating.

First, let’s understand the ‘Sensing Fill’ cycle. This is a standard feature in modern washing machines, like Amana models, that ensures the right amount of water is used for each load. The machine calculates the weight of the clothes, and it uses this information to fill the drum with the corresponding volume of water.

However, at times, the machine may get stuck at this stage, and the ‘Sensing Fill’ message will persist on the display panel.

Reasons for Amana Washer Stuck on Sensing Fill

The main reasons for this problem include issues with the water inlet valve, faulty load sensors, blocked water hoses, and control board malfunctions. Let’s learn about each of these problems and examine how to determine them.

  • Water Inlet Valve Problems:

The water inlet valve regulates the portion of water that gets into your washing machine. If it’s faulty or blocked with mineral residues, water flow may be blocked, driving the washer to stay in the ‘Sensing Fill’ mode.

To check the valve, turn off the water supply and disconnect the hoses from the washer. Check the screens inside the water inlet valve for blockages. If they’re clean and the problem persists, you might need to replace the valve.

  • Faulty Load Sensors:

Amana washers use load sensors to detect the weight of your laundry load. If these sensors fail, they might inaccurately estimate the load weight, causing the washer to remain on the ‘Sensing Fill’ cycle.

Unfortunately, load sensors are not typically user-serviceable parts, and diagnosing a malfunctioning sensor requires technical skills. Consequently, if you suppose an incorrect load sensor, it’s most useful to consult a proficient technician.

  • Blocked Water Hoses:

Blockages in the water supply hoses can also keep your washer stuck on ‘Sensing Fill.’ To verify this, disconnect the hoses from the washer and check for obstructions. Also, inspect the screens in the water inlet for blockages.

If you notice any obstructions, clean the hoses thoroughly. If they’re too unraveled or impaired, you might require to substitute them.

  • Control Board Malfunctions:

A faulty control board can cause your washer to get stuck on the ‘Sensing Fill’ stage. The control board is like the washing machine’s brain, sending signals to various components to perform their respective functions. If it malfunctions, it may not send the right signals, thus causing the machine to remain stuck in one stage.

Resetting the control board can often solve the problem. To do this, detach the washer from the power source for about a minute, then reconnect it. If the problem continues, you might require to substitute the control board, which should be done by a skilled technician to bypass additional difficulties.

An Amana washer stuck on ‘Sensing Fill’ can be a result of various issues, ranging from water inlet valve problems, faulty load sensors, and blocked water hoses, to control board malfunctions.

While some of these issues can be tackled with a basic understanding of how your washing machine operates, others might require professional help. Remember, if you feel unsure about any of these steps, it’s always safe and advisable to reach out to a professional appliance technician.

And even though dealing with a malfunctioning appliance can be frustrating, understanding the cause of the problem can help you take the right steps towards a solution. We hope this guide will help you troubleshoot your Amana washing machine effectively, and restore the convenience of a fully functioning laundry appliance in your home.

  • Pressure Switch Issues:

Your washer’s pressure switch could be a less obvious culprit. This switch tells your machine when it has enough water. If it’s faulty, it might fail to give the go-ahead to stop filling, leaving your washer in a perpetual ‘Sensing Fill’ mode.

You can usually locate the pressure switch inside the control panel of your machine. You might want to check your washer’s manual or search online for specific instructions related to your model. If the pressure switch appears damaged or if testing it is beyond your comfort zone, contact a professional for further assistance.

  • Door Lock Assembly:

Interestingly, a problem with the door lock assembly can also cause your washer to get stuck on the ‘Sensing Fill’ stage. The machine won’t start the wash cycle if it thinks the door is open.

If your washer’s door isn’t locking properly, check the latch for any damage. Also, inspect the door strike (the part on the door that engages the latch) for wear and tear. You might need to replace these components if they are worn out or damaged.

  • Water Level Sensor:

Similar to the pressure switch, a malfunctioning water level sensor can also cause problems. This sensor monitors the tub’s water level and sends a signal to the control board when it’s time to move to the next cycle. If the sensor is faulty, it might send inaccurate signals, resulting in your washer being stuck on ‘Sensing Fill.’

To inspect this sensor, you’ll need to refer to your washer’s manual as the sensor location can vary between models. If you suspect a faulty water level sensor, it’s best to consult a professional technician.

  • Software Glitch:

Finally, your Amana washing machine may be stuck on the ‘Sensing Fill’ stage due to a simple software glitch. Just like our computers and smartphones, our appliances also rely on software that can sometimes glitch.

To address this, a “hard reset” could be an effective solution. Unplug your washer from the electrical outlet, pause for a minute, and then plug it back in.

The reboot might resolve the software glitch, and your washer may operate normally again.

How to Fix Amana Washer Stuck on Sensing Fill Issue?

When an Amana washer is stuck on the “Sensing Fill” stage, it could be due to several reasons, including problems with the water supply, the pressure switch, or the control board. Here are some steps you can take to fix the problem of “Amana Washer Stuck on Sensing Fill”.

Check the Water Supply:

    • Make sure the water supply valves for both the hot and cold water are fully open.
    • Check the water inlet hoses for any kinks, blockages, or leaks. You can do this by disconnecting the hoses and running water through them into a bucket or sink.
    • Also, inspect the screens at the hose connections on the washer for any debris or deposits that might be restricting the water flow. If these are dirty, you can clean them with a brush or replace them if they’re damaged.

Check the Load Size:

  • Sometimes the washer can get stuck on the sensing fill cycle if the load is too small. Try adding a few more items and see if that resolves the issue.
  • Similarly, an unbalanced load can also cause this problem. Make sure the load is evenly distributed.

Reset the Washer:

Unplug the washer from the power outlet and wait for about 1 minute. This will allow the washer’s internal memory to reset. After waiting for a minute, plug it back in and try running a cycle to see if the problem is fixed.

If your Amana washing machine has a reset button, press and hold it for about 5 seconds to reset the washer.

  1. Inspect the Lid Switch and Door Lock:
    • The washer won’t fill with water if it thinks the lid is open. Make sure the lid is properly closed. If you suspect the lid switch or door lock could be faulty, you may need to consult with a professional or replace the part if you are comfortable doing so.
  2. Inspect the Pressure Switch:
    • The pressure switch, also known as the water level switch, tells the washer when it’s full. If this part is malfunctioning, the washer might get stuck on the sensing fill cycle. The pressure switch is typically located inside the control panel, and testing or replacing it may require a professional’s help unless you’re experienced with appliance repairs.
  3. Check the Control Board:
    • If none of the above steps work, the problem could be with the washer’s control board. The control board governs all of the washer’s functions, and a malfunctioning control board could be causing the sensing fill issue. Unfortunately, a faulty control board is a major problem, and repairing or replacing it should only be done by a professional.

Note: If none of these solutions works, or if you’re uncomfortable performing these checks and fixes yourself, it would be best to consult a professional repair service to avoid damaging your washing machine further.

Also Read:

Conclusion: 

While common issues such as water inlet valve problems, blocked water hoses or control board malfunctions often cause the ‘Sensing Fill’ problem, it’s important not to overlook less common potential culprits like pressure switch issues, problems with the door lock assembly, a faulty water level sensor, or even a simple software glitch.

If you find yourself unsure or hesitant, it is always advisable to seek assistance from a professional. Troubleshooting can be intricate, and experts possess the essential expertise and tools to accurately and safely diagnose and resolve the issue.

Remember, your washing machine is an essential appliance, and understanding its workings can help ensure it provides many years of reliable service. Through this extended guide, we hope to have provided you with comprehensive insight into tackling the ‘Sensing Fill’ issue, thereby minimizing your inconvenience and maximizing your washer’s efficiency.

Karan Bhardwaj

Karan Bhardwaj is a technology writer and blogger with over 8 years of experience. He is passionate about staying on top of the latest advancements and innovations in the world of tech and enjoys breaking down complex topics into easily digestible content. Follow Him: Facebook Twitter Blog

You may also like...